Bora Centipede 2 ft. L x 4 ft. W x 2.5 ft. H Folding Work Table Steel 1500 lb. capacity Gray/Yellow

A GREAT WORK STAND AT A GREAT PRICE
I JUST RECEIVED MY NEW CENTIPEDE TODAY AND SET IT UP IN ABOUT 30 SECONDS. I ABSOLUTELY LOVE IT. I PLACED A 2’ X 4’ PIECE OF PLYWOOD AS A TABLE, PUT THE TWO INCLUDED CLAMPS CATTY CORNER IN THE SLOTS IN THE CENTIPEDE AND WAS SET UP. SOLID, STATIONARY AND SECURE! I THEN PUT MY DEWALT 8-1/4” JOB SITE SAW ON THE PLYWOOD AND STARTED CUTTING. SOLID AS A ROCK.THE BORA CENTIPEDE IS MORE STABLE THEN THE TWO SAW HORSES I USED BEFORE I RECEIVED THIS MARVELOUS STAND. AFTER I FINISHED CUTTING, IT TOOK LESS THEN A MINUTE TO TAKE THE CLAMPS OFF, STORE THE PLYWOOD AND FOLD THE STAND UP. I NOW FIND IT HARD BELIEVE I WAS ON THE FENCE ABOUT PURCHASING IT.THE ONE THING I CAN SAY IS IT IS A HASSLE PUTTING THE STAND IN THE PROVIDED BAG. THAT IS PROBABLY WHY THE BAG IS FOLDED IN THE BOX RATHER THAN HAVING THE STAND STORED IN THE BAG IN THE BOX. I THINK AFTER I GET THE HANG OF IT THE STAND WILL BE EASIER TO PUT IN THE BAG AFTER USE.ONE MORE THING, THE STAND COMES WITH TWO CLAMPS AND FOUR CORNER PIECES TO BE ABLE TO USE WITH 2 X 4’S. ALTHOUGH THEY ARE ALL MADE OF PLASTIC, THEY ARE WELL MADE AND I AM SURE WILL LAST FOR MANY YEARS.IF YOU ARE ON THE FENCE, PULL THE TRIGGER, YOU WILL NOT BE SORRY!!!

great product that can be put away easily and does not take up much space
really love this centipede – would buy again (actually I plan to get another one in the near future)

Centipede with T-slot top
Very Handy work tableLIKES- Many clever add on products. Non-slip pads that insert into benchdog holes will be handy for sanding & router work. Benchdog clamps will work for simple applications.- setup is relatively fast. See Dislikes below.DISLIKE- Setup of Centipede & T-track top is awkward. Yuo must assemble the keys (see photo) up through holes in the Centipede base and into special shaped holes in the top. Then you turn the key to lock the two together. It takes a lot of wiggling the assembly to get each of the 6 keys in.CONCLUSIONI enjoy using this bench. But if you’re buying it for the rapid setup. Take this into consideration.

Nailed it!
The Bora Centipede is one of those “Where have you been all my life?” products. I knew that I would be buying one (or more), and it doesn’t disappoint. However, it took a great deal of deliberation to figure out WHAT to buy. I’m adding my thoughts to the huge number of (well-earned) positive reviews in the hope that they may be useful to you if your finger is twitching over the “Buy” button because the devil’s in the details.I have several use cases for this, but highly portable assembly space and/or cutting surface and the need to break down sheet goods into more manageable pieces are at the top of the list. I’m fairly tall and like a taller work surface, but I ultimately opted for two of the 30″ version without Bora’s folding work surface. Here’s how I got there.The Portamate can only be used at full extension, so a 2×4′ one can only be 2×4′. While I needed a 4×8 space for my second use case, 2×4′ seemed far more practical under more circumstances, so I bought two. The supplied lumber brackets let me tie them together into a single 4×8′ “surface.” Each one comes with 4 brackets, so if this is something you may want to do, buy another 4 brackets to provide better support in the center. With these, your own lumber and a sacrificial sheet of EPS, you have a “track saw station.”I opted for the 30″ stands because oddly, the 36″ models are not available with bags. Yet. The stands come with a fair number of accessories and I wanted to corral everything in its own bag because this reduces the likelihood of my leaving something behind at a job site. Also, for the second use case, 30” is plenty of height.Bora does make height extenders, but I have passed on those (for now) because the reviews seem to indicate that they’re fiddlesome.What I bought serves my needs very well. As many others have noted, this spindly looking contraption is a sturdy beast that deploys and recovers in seconds and disappears when not in use. The Centipede work stand is an absolute gem.So, why didn’t I buy the work surfaces? This is NOT a review; I don’t own the work surfaces and cannot speak to their quality or utility directly. These are just my thoughts. My reservation is primarily around shipping. The design seems sound; their ability to fold makes them take up half as much space when stored or stowed. But they’re MDF. If the shipper drops the heavy box on a corner, the MDF gets chipped or broken. If they drop it on the wrong corner, the work surface may be unusable. I may buy them in the future, but only at a retail store or once I see reviews that indicate better protective packaging. More than likely, I’ll make my own.The work surfaces are also available with dog holes or dog holes and T-track. Note that they’re available with Imperial or Metric dog holes; reviewers who complained about the dog holes being too small bought the wrong one. The ones with T-track come with a hefty price tag, but if you don’t need to make precision, repeatable cuts, the system is still a disruptively priced, highly mobile assembly space. Assembly space is baked into competitor systems such as the more expensive Kreg ACS and the wickedly more expensive Festool MFT, but those are better cut stations.Overall, while the work surfaces would complete my Centipedes, MDF is “chippy” and insanely heavy compared to Melamine laminated plywood. The fit and finish of Bora’s products is generally very good, but in my view, their choice of material isn’t great in this case.

Fijn lekker compact en ligt in gewicht

Al igual que el de 12 soportes, es una herramienta imprescindible para tener un banco de trabajo portatil

値段はしますがそれなりにしっかりしていて作業台は当たり前ですがアウトドアテーブルや人が集まった時の仮設テーブルとしてなかなか良いですしっかりしていてグラグラしないのが値段だけの事あります。