MILWAUKEE ELECTRIC TOOL 49-22-8510 Milwaukee Kit Right Angle Attachment, 9.5″ x 1.75″ x 6″

Small, but very sturdy all-metal construction, should last a long time
I like this right-angle attachment a lot, especially the sturdy metal construction and the small size. I use it with my cordless drill when there’s not enough space to fit the drill + bit, then I come in from the side with this right-angle attachment. My Bosch 12-volt drill is rated at 265 inch-pounds of torque, and the Milwaukee attachment is rated at 235 inch-pounds, so they are pretty well matched. The product info sheet lists a few other limitations:- drives screws up to #8 x 3″- flat boring bits up to 1″ dia [spade bits]- twist drills up to 1/8″ [in my opinion, it will easily handle bigger drill bits – after all, they say it can handle a 1″ spade bit!]- 1750 rpm max- not for impact drivers or corded power toolsThe chuck collar has to be pulled forward (outward) both to insert and remove hex bits. With my usual hex bit holder, I can push hex bits into the chuck without pulling the collar forward, but not with this chuck. Therefore you always need two hands at the chuck, inserting and removing bits, a minor inconvenience.If you are really tight on space, you can use the very short hex bits, the ones that are about 1″ long. The total required space for the attachment + bit is then about 2-3/8″, not including any extra space that the drill might need. The interior of the chuck is strongly magnetic, but only once the bit is fully inserted. When using the very short bits, there’s very little of the bit sticking out of the chuck to grab on to. To break the considerable magnetic force, you might need to use pliers to grab short bits, but regular bits are easy to pull out by hand (once you pull out the chuck collar). The overall length of the attachment is 6-3/16″, including the full length of the drive shaft.I have used this right-angle attachment to drill holes for electrical wires, using a 5/8″ Irwin Speedbor, the kind with the lead screw and three spiral flutes. These drill bits need a lot of torque, and 5/8″ is the biggest Speedbor that I can use with my cordless drill without overtaxing the drill. The Milwaukee right-angle attachment handled the torque just fine, although I was extra careful not to let the Speedbor bit bind in the hole, which can cause kickback and extra strain.Note that the attachment’s drive shaft has two different diameters: The very end has a 1/4″ hex shank, but farther up the shaft, it expands to 5/16″ hex, which they say you can use for higher torque applications.The red handle is quite adjustable. By unscrewing the handle a few turns, you can pivot the handle from 0 to 90 degrees from the body of the attachment (in four steps), then tighten the handle to lock it in place. But you can also rotate the metal collar that the handle attaches to, so the handle can stick out of either side of the attachment body, or the top or bottom (there are 12 detents as you rotate the collar all the way around the attachment body). To rotate the collar, loosen the red handle, tilt it all the way towards the chuck end (past 90 degrees, which unlocks the rotating collar), then twist the handle/collar assembly around the body of the attachment. Once you tilt the handle back, it locks the collar, then you tighten the handle itself.One other unobvious feature: There is a small hole in the body of the attachment, at the chuck end, that the instructions say is a lubrication port, for light oil or lithium grease. It’s not clear how to use this port, because there is no fitting, just a small hole.The product package says the attachment is made in Taiwan.Although it’s pricey, the Milwaukee right-angle attachment is very well made. Overall, I like it a lot, and would recommend it.

The Best Angle Drill Attachment Money Can Buy
If you are considering trying to drill in a tight area, or inside a wall, do not consider buying any other right angle drill attachment than this one.I’m a professional TV Installer and this is the most important drilling tool in my arsenal. I have killed probably 10 or more other brands/types of right angle drills and drill bit attachments, they always end up breaking.The chuck slides down, you slide in a hex drill bit, and lock it back in place, nice and smooth, and holds on to the bit well.I’ve been using this Milwaukee now for about four months with no signs of it breaking down. It’s extremely well built. I use it typically with a cordless 18V drill set on the lower RPM setting, and Bosch Daredevil paddle bits (another best in class, check out those bits here for blasting through studs). http://www.amazon.com/Bosch-Daredevil-DSB5013P-13-Piece-Spade/dp/B002GU6QAA/ref=sr_1_1?ie=UTF8&qid=1362513836&sr=8-1&keywords=bosch+daredevilThis is small enough to fit into a single gang hole, and you can loosen the red handle to allow you to rotate the entire head of the right angle attachment to the angle you need, then screw down the red handle to lock in place. We’ve put this thing through the ringer and it has not died on us yet.We’re typically using it to drill through a stud inside a wall with a paddle bit, fitting it through a single gang hole, and then getting right, left, up or down in a tight space. For anybody that has tried this you know how hard it is, and how demanding on the tool and bit it can be. You’ve probably also tried a similar tool or attachment and my guess is it eventually died.Spend the extra few dollars for this attachment and you will not regret it.

This is an ultimate tool to have, works amazingly and like any Milwaukee product it’s quality.

It’s a nice quality item but to make it work with a drill bit (as I needed it) you need an adapter or drill bits with the correct fitting. All in all a great product.

Simple and affective