Nilight Flush Mount LED Light Pods 2PCS 6 Inch 39W Upgraded Spot Flood Combo Beam Driving Work Lighting Backup Reverse Grill Mount Lights for Offroad Truck Tractor SUV ATV UTV Golf Cart Boats

Bright, good quality
Very bright, easy to mount with mounting diagram provided. Mounted them on the bumper of my 01 Yukon with no problems. Just needed to trim a few of the heat deflectors on back of the light to fit with the tow package but no problem. Easily as bright as some of my Auxbeam pods

Wow – just awesome
I am in love with these lights. They are super powerful and light up the darkness, gospel style. I cut them into my rear bumper, and am glad I didn’t use mounts. I have the aux switches in my console so they are super convenient to illuminate.A couple of things I wish I’d known after investing two hours:1. They do not come with a rubber gasket so if your surface isn’t perfectly flush like my bumper, know that is won’t mount flush.2. The wire that is used is probably 18 gauge at best. It’s very small and the feeder wire I used was #14 so I had to use some creativity crimping. I wish the wire was a touch bigger.3. If you are drilling through steel, make sure you have good bits and start a large pilot hole. If you remove the light to finish drilling, it won’t be perfect as the bit walks a bit as I’m sure you know.4. Obviously make sure you have nothing behind the mount point.5. A nice upgrade would be black mounting bolts, if you are really concerned about the look, you may want to get black bolts.6. When you trace your template (provided) make sure you tape it down as it will move. Also, take the line out with your cut. The template runs a little small / actual and gives you no room to wiggle.Hope these tips are helpful, they are very bright and seem to be good quality.

Bright and they work
These are bright, but much more of a scattered flood than I was hoping for there’s not much focus if any for the light beam. I have other nitlight lights on another truck they are a little smaller and have a more focused beam to them. Install is straight forward and difficult do to my choice of 1/4″ diamondplate on my homemade bumper should be easy on anything else just make sure you aren’t planning on cutting the holes with a 4.5″ grinder there’s no room for the corners to cover any overcut. So I started with grinder ended with Sawzall. They look nice very low profile now I just need to figure out how to keep them from lighting up the sky and keep them a bit more tamed toward the ground. This is not a defect just a flood light with a very impressive spread more than my personal preference

Looks like stock equipment. Easy installation. Great illumination!
Wasn’t too sure about these when I saw them online. I was expecting something cheaply made and something that felt equally cheap in my hand. I was pleasantly surprised when I opened the box and unpacked the contents. Everything was well packaged and nothing was scratched or damaged. The lights are heavy gauge metal body construction and are very sturdily built. I wouldn’t recommend using the cardboard template though. U installed the first one without using it and everything came out good. Using the template, the holes were off a little and had to be bored out a little larger in order to get the bolt through the hole. Just slide the light through the cutout you make then mark the mounting holes and drill – perfect fit. I can’t wait to see the difference these things make. As you can see in the picture, the bag contains bolts, buts and washers. It also contains an allen wrench to tighten the bolts.I could barely tell when my factory reverse lamps came on. After installing these lamps, I can clearly see when I am backing up. I get great illumination at least 50 feet behind my truck now; more than enough to safely back up without worry. I hope to get a long life of use from these, but if I were still deciding on which set to buy, I’d choose these.As I was installing them, a neighbor came by and said they looked great on the truck and that they didn’t look aftermarket or out of place at all.All-in-all I would say the install is fairly easy with minimal “mechanical knowledge” required. Tools required: 4 1/2″ grinder to cut through the bumper, needle nose vice grips, marker, drill with bit. On a 1 (easy) to 10 (hard) scale I’d give the install procedure a 2.The last picture shows the lights on. You can see the OEM reverse lights under the tail lights Huge difference.******UPDATE******About a week after installing the lights, I noticed one light was not working. I have not figured out yet what the problem is. I was thinking it was shorting out but that doesn’t seem to be the problem. If I tap the back of the light, it will turn on (as long as it is suppose to be on). Now I am thinking it is defective.

Bright lights easy to install

These are very bright. A lot brighter then my other ones that were lower wattage. The lower wattage ones were as bright as my low beam, no fashing lights at me at night. Now these one’s are a lot more wattage and are as bright as my high beam. Makes it a lot better seeing dear and other animals running out in front of you at night. I don’t advise anyone to drive around all day with these on, makes your alternator work double time, alternators are made to last just so long, with most charging and high amp demand being at night, and then running them all day to, well you get the math on your alternator. I hope these lights last longer then the lower wattage ones did, two years. Thank you.

Se sienten bien aúno los instalo pero se ve de buenos materiales después actualizo la reseña